nach oben

The International Journal of Advanced Manufacturing Technology

Erschienen in:

02.04.2024 | ORIGINAL ARTICLE

2017A Alloy surface layer after flow burnishing with glass microspheres

verfasst von: Katarzyna Korzynska, Tomasz Zarski, Wojciech Zeglicki, Jan Zwolak

Erschienen in: The International Journal of Advanced Manufacturing Technology | Ausgabe 5-6/2024

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

This study presents an unconventional flow processing technique that uses glass microspheres instead of abrasives. The fundamentals of flow machining with glass microspheres, including microsphere flow burnishing (MFB) and the conditions necessary for cutting or plastic deformation of a surface to occur during MFB, are determined. Details on such conditions are lacking, and therefore, this study attempts to define these conditions. To this end, MFB was experimentally confirmed to be a burnishing process, and the effects of MFB and abrasive flow machining (AFM) on 2017A aluminum alloy were compared. Both processes achieved a surface roughness (Sa) of < 0.5 μm, while MFB yielded higher values of surface microhardness and compressive stress. The effects of basic process parameters on the MFB and AFM results (workpiece weight loss and Sa) were compared experimentally, and the corresponding mathematical models were established. Utilizing these relationships, MFB parameters can be selected so as to obtain the most favorable surface layer for the expected operating conditions.

Vorheriger Artikel Study on the regulation of deformation uniformity and microstructure law in the forming of gear shafts by cross wedge rolling

Nächster Artikel Coupled filling-curing simulation and optimized design of cure cycle in liquid composite molding

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Nur mit Berechtigung zugänglich

Rana V, Petare A, Jain NK, Parey A (2022) Using abrasive flow finishing process to reduce noise and vibrations of cylindrical and conical gears. Proc Inst Mech Eng Pt B J Eng Manufact 236(10):1341–1354. https://doi.org/10.1177/09544054221075875CrossRef

Fu Y, Wang X, Gao H, Wei H, Li S (2016) Blade surface uniformity of blisk finished by abrasive flow machining. Int J Adv Manuf Technol 84:1725–1735. https://doi.org/10.1007/s00170-015-8270-0CrossRef

Wang XC, Wang CC, Wang CY, Sun FH (2018) Approach for polishing diamond coated complicated cutting tool: abrasive flow machining. Chin J Mech Eng 31:97. https://doi.org/10.1186/s10033-018-0296-4CrossRef

Ni C, Shi Y (2022) Abrasive flow finishing of micro-channel produced by selective laser melting. Mater Manuf Process 1–15. https://doi.org/10.1080/10426914.(2022).2105881

Liu G, Li J, Zhu S, Zhu X, Qu J, Zhang X (2022) Experimental and numerical analysis of the assisted abrasive flow of magnetic particles on the polishing of fuel injection nozzles. Magnetochemistry 8:1–19. https://doi.org/10.3390/magnetochemistry8030035CrossRef

François M, Han S, Segonds F, Dupuy C, Rivette M, Turpault S, Mimouna M, Salvatore F, Rech J, Peyre P (2021) Electromagnetic performance of Ti6Al4V and AlSi7Mg0.6 waveguides with laser beam melting (LBM) produced and abrasive flow machining (AFM) finished internal surfaces. J Electromagn Waves Appl 35(18):2510–2526. https://doi.org/10.1080/09205071.(2021).1954554CrossRef

Li J, Tian G, Yin Y, Shi G, Zhang J, Zhang XM (2023) Effectiveness analysis of abrasive flow machining on elbow inner-surface finish. Int J Adv Manuf Technol (preprint). https://doi.org/10.21203/rs.3.rs-2430779/v1CrossRef

Samoilenko M, Lanik G, Brailovski V (2021) Towards the determination of machining allowances and surface roughness of 3D-printed parts subjected to abrasive flow machining. J Manuf Mater Process 5:111. https://doi.org/10.3390/jmmp5040111CrossRef

Sambharia JK, Mali HS, Garg V (2018) experimental investigation on unidirectional abrasive flow machining of trim die workpiece. Mater Manuf Process 33:651–660. https://doi.org/10.1080/10426914.2017.1364847CrossRef

10.

Kim YG, Kim KJ, Kim KH (2021) Efficient removal of milling burrs by abrasive flow. Int J Precis Eng Manuf 22:441–451. https://doi.org/10.1007/s12541-020-00455-0CrossRef

11.

Kim KJ, Kim YG, Kim KH (2022) Characterization of deburring by abrasive flow machining for AL6061. Appl Sci 12:2048. https://doi.org/10.3390/app12042048CrossRef

12.

Gov K, Eyercioglu O (2018) Effects of abrasive types on the surface integrity of abrasive-flow-machined surfaces. Proc Inst Mech Eng B J Eng Manuf 232:1044–1053. https://doi.org/10.1177/0954405416662080CrossRef

13.

Dixit N, Sharma V, Kumar P (2022) Experimental investigations into abrasive flow machining (AFM) of 3D printed ABS and PLA Parts. Rapid Prototyp J 28(1):161–174. https://doi.org/10.1108/RPJ-01-(2021)-0013CrossRef

14.

Hashmi AW, Mali HS, Meena A (2021) An experimental investigation of viscosity of a newly developed natural polymer-based media for abrasive flow machining (AFM) of 3D printed ABS parts. J Eng Res. https://doi.org/10.36909/jer.13643CrossRef

15.

Singh S, Sankar MR, Jain VK (2018) Simulation and experimental investigations into abrasive flow nanofinishing of surgical stainless steel tubes. Mach Sci Technol 22:454–475. https://doi.org/10.1080/10910344.2017.1365897CrossRef

16.

Zeglicki W, Korzynska K, Palczak A (2013) Abrasive flow machining. In: Korzynski M (ed) Nonconventional finishing technologies. Polish Scientific Publishers PWN, Warsaw, pp 141–158

17.

Kumari C, Chak SK (2019) Study on influential parameters of hybrid AFM processes: a review. Manuf Rev 6:23. https://doi.org/10.1051/mfreview/(2019)022CrossRef

18.

Wang H, Gao H (2023) Influence of wall-slip on material removal in abrasive flow machining. Int J Mech Sci 108727. https://doi.org/10.1016/j.ijmecsci.2023.108727.

19.

Ji R, Qi Z, Chen J, Zhang L, Lin K, Lu S (2023) Li Y Numerical and experimental investigation on the abrasive flow machining of artificial knee joint surface. Crystals 13:430. https://doi.org/10.3390/cryst13030430CrossRef

20.

Chawla G, Mittal VK, Mittal S (2021) Experimental investigation of process parameters of Al-SiC-B4C MMCs finished by a novel magnetic abrasive flow machining setup. Walailak J Sci Techno 18(15):9885. https://doi.org/10.48048/wjst.2021.9885CrossRef

21.

Dixit N, Sharma V, Kumar P (2022) Experimental investigations into ultrasonic assisted magnetic abrasive flow machining process. Mater Manuf Process 1–16. https://doi.org/10.1080/10426914.(2022).2146712

22.

Teng X, Zhang G, Zhao Y, Cui Y, Li L, Jiang L (2019) Study on magnetic abrasive finishing of AlSi10Mg alloy prepared by selective laser melting. Int J Adv Manuf Technol 105:2513–2521. https://doi.org/10.1007/s00170-019-04485-5CrossRef

23.

Tan Y, Ni Y, Wu J, Li L, Tan D (2023) Machinability evolution of gas–liquid-solid three-phase rotary abrasive flow finishing. Int J Adv Manuf Technol 1–20. https://doi.org/10.1007/s00170-022-10761-8

24.

Cheng KC, Wang AC, Chen KY, Huang CY (2022) Study of the polishing characteristics by abrasive flow machining with a rotating device. Processes 10:1362. https://doi.org/10.3390/pr10071362CrossRef

25.

Dixit N, Sharma V, Kumar P (2022) Mathematical modeling of material removal and surface roughness in ultrasonic-assisted magnetic abrasive flow machining process. J Manuf Sci Eng 144(12):121009. https://doi.org/10.1115/1.4055053CrossRef

26.

Hashmi AW, Mali HS, Meena A, Ahmad S, Tian Y (2023) A novel eco-friendly abrasive media based abrasive flow machining of 3D printed PLA parts using IGWO and ANN. Rapid Prototyp J. Vol. ahead-of-print No. ahead-of-print. https://doi.org/10.1108/RPJ-04-2023-0136

27.

Singh S, Kumar H, Kumar S, Chaitanya SA (2022) Systematic review on recent advancements in abrasive flow machining (AFM). Mater Today Proc 56:3108–3116. https://doi.org/10.1016/j.matpr.(2021).12.273CrossRef

28.

Dhull S, Mishra RS, Walia RS, Murtaza Q, Niranjan MS (2021) Innovations in different abrasive flow machining processes: a review. J Phys Conf Ser 1950(1):012048. https://ui.adsabs.harvard.edu/link_gateway/(2021)JPhCS1950a2048D/10.1088/1742-6596/1950/1/012048

29.

Goyal A, Singh H, Goyal R, Singh R, Singh S (2022) Recent advancements in abrasive flow machining and abrasive materials: a review. Mater Today Proc 56:3065–3072. https://doi.org/10.1016/j.matpr.(2021).12.109CrossRef

30.

Jagadeesh GV, Setti SG (2023) Tribological characterization of ball burnished magnesium alloy by wear-burnishing maps wear maps and artificial intelligence technique. Arab J Sci Eng 48:3111–3131. https://doi.org/10.1007/s13369-022-07025-8CrossRef

31.

Korzynski M, Dudek K, Kruczek B, Kocurek P (2018) Equilibrium surface texture of valve stems and burnishing method to obtain it. Tribol Int 124:195–199. https://doi.org/10.1016/j.triboint.(2018).04.014CrossRef

32.

Korzynska K, Zeglicki W, Korzynski M, Drabczyk M (2020) Flow burnishing with glass microspheres and its impact on the surface condition of 2017A alloy elements. J Manuf Process 58:1297–1303. https://doi.org/10.1016/j.jmapro.(2020).09.035CrossRef

33.

Gorana VK, Jain VK, Lal GK (2006) Forces prediction during material deformation in abrasive flow machining. Wear 260:128–139. https://doi.org/10.1016/j.wear.(2004).12.038CrossRef

34.

Gorana VK, Jain VK, Lal GK (2004) Experimental investigation into cutting forces and active grain density during abrasive flow machining. Int J Mach Tools Manuf 44:201–211. https://doi.org/10.1016/j.ijmachtools.2003.10.004CrossRef

35.

Kragelsky IV (1965) Friction and Wear. Butterworths, London

36.

Kaczmarek J (1971) Podstawy obróbki wiórowej ściernej i ero-zyjnej [Foundations of machining abrasive machining and erosion machining]. Science Publishing Home WNT, Warsaw

37.

Kaldonski T (2006) Identification tests of stiction characteristics determining abrasive wear course of LH-15 steel. J Mater Process Technol 175:241–245. https://doi.org/10.1016/j.jmatprotec.2005.04.013CrossRef

38.

Lipinski D, Kacalak W (2016) Metrological aspects of abrasive tool active surface topography evaluation. Metrol Meas Syst 23:567–577. https://doi.org/10.1515/mms-(2016)-0043CrossRef

39.

AFM or MFB https://youtu.be/i19utNuWa4Y. Accessed 2023–04–23.

40.

Korzynski M (2022) Metodyka Eksperymentu [Methodology of experiment]. Polish Scientific Publishers PWN, Warsaw

41.

Montgomery DC (2001) Design and analysis of experiments, 5th edn. John Wiley and Sons, Singapore

42.

Korzynski M, Dudek K, Korzynska K (2023) Effect of slide diamond burnishing on the surface layer of valve stems and the durability of the stem-graphite seal friction pair. Appl Sci 13(11):6392. https://doi.org/10.3390/app13116392CrossRef

43.

Maximov JT, Anchev AP, Duncheva GV, Ganev N, Selimov KF (2017) Influence of the process parameters on the surface roughness, micro-hardness, and residual stresses in slide burnishing of high-strength aluminum alloys. J Braz Soc Mech Sci Eng 39:3067–3078. https://doi.org/10.1007/s40430-016-0647-yCrossRef

Titel: 2017A Alloy surface layer after flow burnishing with glass microspheres
verfasst von: Katarzyna Korzynska
Tomasz Zarski
Wojciech Zeglicki
Jan Zwolak
Publikationsdatum: 02.04.2024
Verlag: Springer London
Erschienen in: The International Journal of Advanced Manufacturing Technology / Ausgabe 5-6/2024
Print ISSN: 0268-3768
Elektronische ISSN: 1433-3015
DOI: https://doi.org/10.1007/s00170-024-13480-4

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 5-6/2024

Energy efficiency of Gaussian and ring profiles for LPBF of nickel alloy 718

A comprehensive investigation on the effect of processing conditions on the dry drilling performance of electron beam melting–manufactured Ti6Al4V

Effects of gas tungsten arc welding on the mechanical properties and microstructure of 316L stainless steel by powder bed fusion

An investigation on the suitability of different welding recovery procedures for cold stamping punches in VF800AT steel

A novel five-axis on-machine measurement error prediction model considering positioning errors of machine tool

Research on theoretical prediction method of rivet-forming quality considering different riveted structure parameters

Premium Partner

Marktübersichten