nach oben

Forschung im Ingenieurwesen

Erschienen in:

15.03.2021 | Originalarbeiten/Originals

Influence of running-in operating conditions on the steady-state torque loss of ground spur gears

verfasst von: Carlos M. C. G. Fernandes, João C. Pais, Ramiro C. Martins, Jorge H. O. Seabra

Erschienen in: Forschung im Ingenieurwesen | Ausgabe 2/2021

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

The influence of gear running-in operating conditions on the steady-state efficiency of ground spur gears is not well established. However, it is accepted that less rough surfaces promote better efficiency.

Five ground spur gears with similar surface finishing were submitted to two distinct test stages: (i) running-in stage and (ii) torque loss stage. During the running-in stage, five different running-in operating conditions were conducted to ascertain the influence of the load and temperature on the subsequent steady-state gear torque loss test.

The mass loss and surface roughness parameters were influenced by the running-in operating conditions. However, different surface conditions after running-in had only a transient effect on the torque loss measured subsequently. So, the test campaign allow to conclude that even after a severe running-in operating condition, the gears surface still evolves in a significant way during the torque loss tests.

Vorheriger Artikel Influence of the grid parameters during under voltage ride through (UVRT) testing

Nächster Artikel Assessment of noise attenuating powertrain components

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Nur mit Berechtigung zugänglich

Blau PJ, Komanduri R (1990) Friction and wear transitions of materials: break-in, run-in, and wear-in. J Eng Mater Technol 112(2):254. https://doi.org/10.1115/1.2903318CrossRef

Blau PJ (2005) On the nature of running-in. Tribol Int 38(11-12):1007–1012. https://doi.org/10.1016/j.triboint.2005.07.020CrossRef

Akbarzadeh S, Khonsari M (2011) Experimental and theoretical investigation of running-in. Tribol Int 44(2):92–100. https://doi.org/10.1016/j.triboint.2010.09.006CrossRef

Jamari J (2006) Running-in of rolling contacts, PhD Thesis, University of Twente, Netherlands

Andersson S (1977) Initial wear of gears. Tribol Int 10(4):206–210. https://doi.org/10.1016/0301-679X(77)90021-4CrossRef

Chowdhury SR, Kaliszer H, Rowe G (1979) An analysis of changes in surface topography during running-in of plain bearings. Wear 57(2):331–343. https://doi.org/10.1016/0043-1648(79)90107-8CrossRef

Chengwei W, Linqing Z (1991) Effect of waviness and roughness on lubricated wear related to running-in. Wear 147(2):323–334. https://doi.org/10.1016/0043-1648(91)90189-2CrossRef

Shirong G, Gouan C (1999) Fractal prediction models of sliding wear during the running-in process. Wear 231(2):249–255. https://doi.org/10.1016/S0043-1648(99)00132-5CrossRef

Jeng Y-R, Lin Z-W, Shyu S-H (2004) Changes of surface topography during running-in process. J Tribol. https://doi.org/10.1115/1.1759344CrossRef

10.

Akbarzadeh S, Khonsari M (2010) On the prediction of running-in behavior in mixed-lubrication line contact. J Tribol. https://doi.org/10.1115/1.4001622CrossRef

11.

Akbarzadeh S, Khonsari M (2013) On the optimization of running-in operating conditions in applications involving ehl line contact. Wear 303(1):130–137. https://doi.org/10.1016/j.wear.2013.01.098CrossRef

12.

Zhang G, Liu X, Lu W (2013) A parameter prediction model of running-in based on surface topography. Proc Inst Mech Eng H J Eng Med 227(9):1047–1055. https://doi.org/10.1177/1350650113484097CrossRef

13.

Andersson M, Sosa M, Olofsson U (2016) The effect of running-in on the efficiency of superfinished gears. Tribol Int 93:71–77. https://doi.org/10.1016/j.triboint.2015.08.010CrossRef

14.

Sjöberg S, Sosa M, Andersson M, Olofsson U (2016) Analysis of efficiency of spur ground gears and the influence of running-in. Tribol Int 93:172–181. https://doi.org/10.1016/j.triboint.2015.08.045CrossRef

15.

Sosa M, Sellgren U, Björklund S, Olofsson U (2016) In situ running-in analysis of ground gears. Wear 352-353:122–129. https://doi.org/10.1016/j.wear.2016.01.021CrossRef

16.

Mallipeddi D, Norell M, Sosa M, Nyborg L (2017) Influence of running-in on surface characteristics of efficiency tested ground gears. Tribol Int 115:45–58. https://doi.org/10.1016/j.triboint.2017.05.018CrossRef

17.

Fernandes CMCG, Martins RC, Seabra JHO (2014) Torque loss of type C40 FZG gears lubricated with wind turbine gear oils. Tribol Int 70:83–93. https://doi.org/10.1016/j.triboint.2013.10.003CrossRef

18.

Fernandes CMCG, Marques PMT, Martins RC, Seabra JHO (2015) Gearbox power loss. Part I: losses in rolling bearings. Tribol Int 88:298–308. https://doi.org/10.1016/j.triboint.2014.11.017CrossRef

19.

Mummery L (1990) Surface texture analysis: the handbook. Hommelwerke,

20.

Tallian TE (1967) On competing failure modes in rolling contact. A S L E Transactions 10(4):418–439. https://doi.org/10.1080/05698196708972201CrossRef

21.

Dowson D, Higginson GR (1977) Elasto-hydrodynamic lubrication. Pergamon Press, OxfordMATH

22.

Archard JF (1953) Contact and rubbing of flat surfaces. J Appl Phys 24(8):981–988. https://doi.org/10.1063/1.1721448CrossRef

23.

Brandão JA, Cerqueira P, Seabra JH, Castro MJ (2016) Measurement of mean wear coefficient during gear tests under various operating conditions. Tribol Int 102:61–69. https://doi.org/10.1016/j.triboint.2016.05.008CrossRef

24.

Fernandes CMCG, Marques PMT, Martins RC, Seabra JHO (2015) Gearbox power loss. Part II: friction losses in gears. Tribol Int 88:309–316. https://doi.org/10.1016/j.triboint.2014.12.004CrossRef

25.

Marques PMT, Fernandes CMCG, Martins RC, Seabra JHO (2014) Efficiency of a gearbox lubricated with wind turbine gear oils. Tribol Int 71:7–16. https://doi.org/10.1016/j.triboint.2013.10.017CrossRef

26.

Fernandes CMCG, Marques PMT, Martins RC, Seabra JHO (2015) Gearbox power loss. Part III: application to a parallel axis and a planetary gearbox. Tribol Int 88:317–326. https://doi.org/10.1016/j.triboint.2015.03.029CrossRef

27.

Fernandes CMCG, Marques PMT, Martins RC, Seabra JHO (2015) Influence of gear loss factor on the power loss prediction. Mech Sci 6(2):81–88. https://doi.org/10.5194/ms-6-81-2015CrossRef

28.

Martins RC, Fernandes CMCG, Seabra JHO (2015) Evaluation of bearing, gears and gearboxes performance with different wind turbine gear oils. Friction 3(4):275–286. https://doi.org/10.1007/s40544-015-0094-2CrossRef

29.

SKF (2003) SKF general catalogue

30.

Marshall G, Jonker L (2010) An introduction to descriptive statistics: a review and practical guide. Radiography 16(4):e1–e7. https://doi.org/10.1016/j.radi.2010.01.001CrossRef

31.

Tabachnick BG, Fidell LS (2006) Using multivariate statistics, 5th edn. Allyn & Bacon, Inc, Needham Heights, MA, USA

32.

Touret T (2019) Health monitoring: impact thermique d’un default dans une transmission par engrenages – application aeronautique. Université de Lyon, Lyon

Titel: Influence of running-in operating conditions on the steady-state torque loss of ground spur gears
verfasst von: Carlos M. C. G. Fernandes
João C. Pais
Ramiro C. Martins
Jorge H. O. Seabra
Publikationsdatum: 15.03.2021
Verlag: Springer Berlin Heidelberg
Erschienen in: Forschung im Ingenieurwesen / Ausgabe 2/2021
Print ISSN: 0015-7899
Elektronische ISSN: 1434-0860
DOI: https://doi.org/10.1007/s10010-021-00447-0

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 2/2021

Simulative investigation of ring creep on a planetary bearing of a wind turbine gearbox

Impacts of electrification & automation of public bus transportation on sustainability—A case study in Singapore

Early stage white etching crack identification using artificial neural networks

Usability of SCADA as predictive maintenance for wind turbines

Effects of wake on gearbox design load cases identified from fleet-wide operational data

Assessment of noise attenuating powertrain components

Premium Partner

Marktübersichten