Ausgabe 3/2022
Best of Gears 2022
Inhalt (41 Artikel)
Gear root bending strength: statistical treatment of Single Tooth Bending Fatigue tests results
Luca Bonaiti, Francesco Rosa, Prasad Mahendra Rao, Franco Concli, Carlo Gorla
A comparison of gear tooth bending fatigue lives from single tooth bending and rotating gear tests
Isaac Hong, Zach Teaford, Ahmet Kahraman
Innovative tooth contact analysis with non-uniform rational b-spline surfaces
Felix Müller, Stefan Schumann, Berthold Schlecht
Dynamic load distribution of planetary gear sets subject to both internal and external excitations
Lokaditya Ryali, David Talbot
Experimental investigation of the dynamic load sharing of planetary gearboxes
J. Götz, F. Siglmüller, M. Fürst, M. Otto, K. Stahl
Influences on the excitation behavior of lightweight planetary gearboxes
Julian Theling, Jens Brimmers, Christian Brecher
Influence of thin–rimmed/-webbed gears on transmission dynamic behaviour—Approximate dynamic factor formula
B. Guilbert, P. Velex
Minimum friction losses in wind turbine gearboxes
José I. Pedrero, Débora Martínez-López, José Calvo-Irisarri, Miguel Pleguezuelos, Miryam B. Sánchez, Alfredo Fernández-Sisón
Gear mesh excitation and non-uniform Rational B-Splines
A. Beinstingel, M. Heider, B. Pinnekamp, S. Marburg
Contact characteristics of cycloid planetary gear drives considering backlashes and clearances
Ling-Chiao Chang, Shyi-Jeng Tsai, Ching-Hao Huang
Analyse der Wirkmechanismen im fluidfreien Wälzkontakt mit beschichteten Oberflächen
Sebastian Sklenak, Jens Brimmers, Christian Brecher
Wear simulation of worm gears based on an energetic approach
K. Daubach, M. Oehler, B. Sauer
Prediction of churning losses in an industrial gear box with spiral bevel gears using the smoothed particle hydrodynamic method
B. Legrady, M. Taesch, G. Tschirschnitz, C. F. Mieth
On windage power loss reduction achieved by flanges
Y. Marchesse, M. Ruzek, F. Ville, P. Velex
CFD analysis on the oil flow of a gear stage with guide plate
Lucas Hildebrand, Florian Dangl, Martin Sedlmair, Thomas Lohner, Karsten Stahl
Automation of gearbox design
Marius Fürst, Joshua Götz, Michael Otto, Karsten Stahl
Sensor-integrating gears: wear detection by in-situ MEMS acceleration sensors
Julian Peters, Lorenz Ott, Matthias Dörr, Thomas Gwosch, Sven Matthiesen
Application of genetic algorithms for parameters identification in a developing smart gear system
T. T. Mac, D. Iba, Y. Matsushita, S. Mukai, T. Inoue, A. Fukushima, N. Miura, T. Iizuka, A. Masuda, I. Moriwaki
Feasibility study of measuring instantaneous angular speed of helical gears with magnetoresistive sensors
Yanik Koch, G. Martin, E. Kirchner, D. Quirnheim Pais, R. Slatter
Enhanced loaded tooth contact analysis of hypoid gears within a multi-body-system simulation
Wolf Wagner, Stefan Schumann, Berthold Schlecht
Suitability of the test results of micropitting tests acc. to FVA 54/7 for modern practical gear applications
Nadine Sagraloff, Thomas Tobie, Karsten Stahl
Mode III threshold under Rolling Contact Fatigue and development of a test gearbox for planet gears
Prasad Mahendra Rao, Stefano Foletti, Luca Bonaiti, Franco Concli, Carlo Gorla, Stefano Beretta
Stress calculation on bevel gears with FEM influence vectors
Frederik Mieth, Carsten Ulrich, Berthold Schlecht
Scuffing load capacity calculation of worm gears
Philipp Roth, Michael Hein, Karsten Stahl
Scuffing of cylindrical gears with pitch line velocities up to 100 m/s
J. Vorgerd, P. Tenberge, M. Joop
Calculating component temperatures in gearboxes for transient operation conditions
Constantin Paschold, Martin Sedlmair, Thomas Lohner, Karsten Stahl
Load-Capacity Evaluation of Polyacetal (POM) internal gears according to JIS B 1759:2016 (Effect of number of teeth of pinion)
I. Moriwaki, K. Tatsuoka, K. Kobayashi, W. Nakamoto, D. Iba, A. Ueda
In situ investigation of the influence of varying load conditions on tooth deformation and wear of polymer gears
Christoph Herzog, Michael Wolf, Dominik Schubert, Dietmar Drummer
Operating behavior and performance of oil-lubricated plastic gears
C. M. Illenberger, T. Tobie, K. Stahl
Erratum to: Operating behavior and performance of oil-lubricated plastic gears
C. M. Illenberger, T. Tobie, K. Stahl
Plastic gear remaining useful life prediction using artificial neural network
B. H. Kien, D. Iba, Y. Tsutsui, D. Taga, N. Miura, T. Iizuka, A. Masuda, I. Moriwaki
Tool wear development in gear skiving process of quenched and tempered internal gears
Tassilo Arndt, Jan Klose, Michael Gerstenmeyer, Volker Schulze
Increasing the safety against scuffing of additive manufactured gear wheels by internal cooling channels
Hans-Jörg Dennig, Livia Zumofen, Daniel Stierli, Andreas Kirchheim, Simon Winterberg
Quality improvement of an aluminum gearbox housing by implementing additive manufacturing
P. Barreiro, G. Armutcu, S. Pfrimmer, J. Hermes
Direct flank geometry calculation for face gears
Jonas-Frederick Hochrein, Maximilian Trübswetter, Michael Otto, Karsten Stahl
Approach for multiscale modeling the thermomechanical tool load in gear hobbing
Nico Troß, Jens Brimmers, Thomas Bergs
Consideration of micro-interaction in the modeling of generating gear grinding processes
Patricia de Oliveira Teixeira, J. Brimmers, T. Bergs
Deep nitriding—contact and bending strength of gears with increased nitriding hardening depth
André Sitzmann, Stefanie Hoja, Stefan Schurer, Thomas Tobie, Karsten Stahl
Influence of grinding zones on the tooth root bending strength of case carburized gears
Karl Jakob Winkler, Thomas Tobie, Karsten Stahl
Modelling and prevention of meshing interference in gear skiving of internal gears
Andreas Hilligardt, Jan Klose, Michael Gerstenmeyer, Volker Schulze